The MSP family of analog I/O blocks offers the freedom to use any analog sensor with many models of PLC. Each MSP block provides a single analog input (or output) interface between the PLC and the analog world. Communications between the MSP unit and the PLC is through a patented protocol that provides truly "open" architecture for analog signals to be processed digitally.

The MSP is factory preconfigured to support a specific analog input or output signals, depending on the model. Optionally, the MSP signal range can be reconfigured in the field using the Windows® based configuration software model SCC-CC-A1 (sold separately).

Input Analog Signal
The analog input signal is isolated, filtered, amplified, scaled and/or linearized by the MSP micro-processor and converted to a 16-bt, binary weighted, digital word which is transmitted serially (one bit at a time) at 24 VDC signal levels to the PLC’s discrete I/O port. At the PLC, each binary-weighted bit sent to the discrete input is temporarily stored until all 16 bits have been received. The digital word is then reassembled and its value (proportional to the analog signal) is placed in a working register of choice for decision making by the PLC program.

Output Analog Signal
The numerical value representing a desired analog output signal is placed into a PLC working register of choice. This value is transmitted serially (one bit at a time)at 24 VDC signal levels to the MSP through the PLC ’s discrete I/O port. The MSP scales, linearizes and proportionally converts the digital signal to the voltage or current output signal. The signal is then sent to the isolated output channel for use by a analog actuator connected at the output channel.

SPECIFICATIONS
Isolation: 1500 VAC continuous (3-way, 2-way for excitation).
Inputs: See Ranges Chart below.
Input Impedance: 1G ohm (mV/TC), 55K ohm (V), 82 ohm (C).
Output Impedance: >10M ohm (C), -0 ohm (V).
Power Requirements: 15-32 VDC @ 25 mA - 45 mA.
Accuracy: 0.05% F.S.
CJC Accuracy: 0.2°C over 15 to 55°C (ambient) 1.0°C over -40 to 14°C; .3°C over 56 to 75°C.
Drift: 0.01% F.S. per °C (offset + gain).
Dimensions: 88 mm (H) x 68 mm (D) x 12 mm (W).
Ambient Operating Temperature: -40 to 167°F (-40 to 75°C).
Storage Temperature: -49 to 185°F (-45 to 85°C).
Humidity Conditions: 95% non-condensing.
Mounting: DIN rail (32 mm-G and 35 mm-H).
Connections: Screw terminals for 14-22 AWG.
Weight: 1.4 oz (40 g).
Agency Approvals: UL, cUL, CSA CE.


INPUT/OUTPUT RANGES

INPUT TYPE	RANGE °F	RANGE °C
Type J Thermocouple	-32 to 32 & 32 to 1400	-200 to 0 & 0 to 760
Type K Thermocouple	-328 to 32 & 32 to 2498	-200 to 0 & 0 to 1370
Type T Thermocouple	-328 to 32 & -256 to 752	-200 to 0 & -160 to 400
Type E Thermocouple	-328 to 32 & -148 to 1832	-200 to 0 & -100 to 1000
Type R Thermocouple	32 to 3214	0 to 1768
Type S Thermocouple	32 to 3214	0 to 1768
Type B Thermocouple	32 to 3322	0 to 1832
Type N Thermocouple	-328 to 32 & 32 to 2373	-200 to 0 & 0 to 1300
100 Ohm Plt. 0.00385 DIN RTD	-328 to 1562	-200 to +850
120 Ohm Nickel 0.00628 US RTD	-112 to +392	-80 to +200
1000 Ohm Plt. O.00385 DIN RTD	-328 to +1592	-200 to +850
Potentiometer	0 to 500O min.; 0 to 100KO max.
Current/Voltage	0-20 mADC/ 0 to 10 VDC

ACCESSORIES -- See "Ordering" page
SCC-4W - Power Supply 85 to 265 VAC @ 50/60 Hz.
SCC-CC-A1 - Windows® Software and Cable.
SPS-4W - Power Supply, 4 Watts, 24 Volts, 150 mAmps.
SPS-12W - Power Supply, 12 Watts, 24 Volts, 1.0 Amps.
SPS-24W - Power Supply, 24 Watts, 24 Volts, 2.0 Amps.
SPS-55W - Power Supply, 55 Watts, 24 Volts, 2.3 Amps.
SPS-120W - Power Supply, 120 Watts, 24 Volts, 5.0 Amps.